Flux Model 5 Magnetic Hall Effect 65 Keyboard Support

Flux Model 5 Magnetic Hall Effect 65

Check the Surface: Ensure you’re using a smooth, consistent surface like a mouse pad. Some surfaces can interfere with the sensor tracking.
Clean the Sensor: Dust and dirt can block the sensor. Flip the mouse over and gently clean the sensor area with a soft cloth.
Update Mouse Drivers:
- Open Device Manager on your computer.
- Expand the Mice and other pointing devices section.
- Right-click on your mouse and select Update Driver.
Adjust Mouse DPI Settings: If your mouse has DPI buttons, try lowering or increasing the DPI to adjust the sensitivity.
Test USB Port: Plug the mouse into another USB port to ensure it’s not a port issue.

Check Connection:
- Ensure the keyboard is firmly connected to the USB port or, if wireless, that it’s properly paired and charged.
Enable Lighting in Software:
- Open your keyboard’s software and navigate to the Lighting section.
- Ensure that the RGB or backlighting is enabled.
Check Power Settings:
- Some gaming keyboards have power-saving modes that disable lighting. Disable this setting in the software.
Update Keyboard Firmware:
- Look for any available firmware updates in the keyboard’s software.
- Follow the prompts to update the firmware.
Test on Another USB Port: Sometimes, insufficient power from a USB port can prevent lighting from functioning. Try a different port, preferably a USB 3.0.

Test in Anti-Ghosting Mode:
- Some gaming keyboards have an anti-ghosting feature. Ensure it is enabled in the keyboard software.
- Test the keyboard by pressing multiple keys simultaneously to check if the problem persists.
Switch to N-Key Rollover Mode:
- Many gaming keyboards support N-Key rollover (NKRO). In the software, ensure NKRO is activated to allow multiple key presses without interference.
Update Keyboard Software:
- Open the keyboard’s companion software and check for updates.
- Install any available updates that might fix ghosting issues.
Change USB Port: Ghosting can sometimes be caused by a lack of sufficient power. Switch the keyboard to a different USB port, preferably one on the back of the computer.
Use USB Extension Cables Properly: If you’re using a USB extension, try removing it and connecting the keyboard directly to the PC to avoid interference.

Clean the Keycaps:
- Remove the problematic keycaps using a keycap puller.
- Clean the area under the keys with compressed air or a soft brush.
Check for Software Key Delays:
- Open the keyboard’s software and check for any settings that may adjust key repeat delays.
- Set the Key Repeat Rate to a more suitable speed.
Adjust Repeat Settings in Windows:
- Go to Control Panel > Keyboard.
- Adjust the Repeat Delay and Repeat Rate settings to prevent keys from registering multiple times.
Reinstall Keyboard Drivers:
- Open Device Manager.
- Right-click on the keyboard under Keyboards and select Uninstall Device.
- Restart your computer, and the driver should reinstall automatically.
Lubricate Mechanical Switches:
- If using a mechanical keyboard, you can apply switch lubricant (if appropriate) to the sticking switches. Be sure to research the correct way to lubricate your specific keyboard.

Reconnect the Keyboard:
- Unplug the keyboard from the USB port, wait a few seconds, and plug it back in.
- If using a wireless keyboard, ensure it’s properly paired and the battery is charged.
Try Another USB Port:
- Plug the keyboard into a different USB port. Use a direct port (no hubs) for troubleshooting purposes.
Check Device Manager:
- Open Device Manager.
- Expand the Keyboards section and look for any yellow warning symbols.
- Right-click the keyboard and select Update Driver.
Test on Another Computer:
- Plug the keyboard into another computer to see if it is recognized. This will help determine whether the problem is with the keyboard or your computer.
Check BIOS Settings:
- Restart your computer and enter the BIOS (press F2, Del, or Esc during boot-up, depending on your system).
- Check if the keyboard is recognized at the BIOS level. If not, you may need to reset the BIOS or check for hardware issues.

All Products

Order Information